The Model VFG-Model Telephones are surface bulkhead mounted and ideally located in low noise areas such as
State Rooms and Offices. An internal audio signaling device is used to signal an incoming call.
The magneto generator, internal audio signaling device, selector switch, handset and handset brackets are mounted
on the cover. The terminal blocks are mounted within the back box.
Both the handset bracket and the main telephone enclosure are fabricated with polycarbonate and are finished in a
black powder coat. The phone is equipped with a single action push to release locking button. The receiver and
transmitter capsule units are identical and interchangeable. In addition to the transmitter and receiver units, there
is a “Press to Operate” pushbutton switch mounted on the handset for convenience. The standard coiled cord of the
handset is one foot long and 6 feet when fully extended.
Features:
- Cost Effective and Proven
- Virtually Indestructible, Flame Retardant
- Operates in Extreme Conditions
- Operates Continuously With No Maintenance
- Operates Without Batteries or External Power Source
- No Software Required
- Meets or Exceeds Title 46, CFR, Subpart 113.30-3(b)
- Secure Locking Bracket For Handset
The Model VFG-WTH are Watertight Voice Powered Telephones that are located mainly in areas, such as the Bow, Stern,
Bridge Wings and Quarter Decks, where exposure to the elements is unavoidable. An audio signaling device is used to signal
an incoming call. A remote watertight under dome bell is provided with a 6 inch diameter brass gong. The enclosure is
fabricated with fiberglass reinforced polyester. It is finished in light gray. All communication components are mounted inside
the watertight enclosure.
Two molded clips are used to secure the hinged door to the box. Mounting brackets are provided for bulkhead installation. A
rubber gasket is secured along the door channels to provide a watertight seal. The installer can either nipple the bell on top of the enclosure, with a 1/2″ NPT entrance hole or mount it at a remote location. The phone is equipped with a single action push to release locking button. The receiver unit and the transmitter units are identical and interchangeable. In addition to the
transmitter and receiver units, there is a “Press to Operate” pushbutton switch mounted on the handset for convenience. The
standard coiled cord of the handset is one foot long and expands to six feet long when fully extended.
Within the phone is a 110 VAC heater and temperature control thermostat to prevent moisture from being collected inside the
telephone and enclosure.
Features:
- Cost Effective and Proven
- Virtually Indestructible, Flame Retardant
- Operates in Extreme Conditions
- Operates Continuously With No Maintenance
- Operates Without Batteries or External Power Source
- No Software Required
- Meets or Exceeds Title 46, CFR, Subpart 113.30-3(b)
- Secure Locking Bracket For Handset
The Model VFG-FLR Series are Flush Mounted Telephones that are mainly located in medium noise areas such as Control
Rooms and Offices. An audio signaling device is used to signal an incoming call.
When there is more than one voice powered telephone in the same area, the indicator light identifies which telephone is being called. In a wide, noisy working area, the latching relay may be employed to sound an additional audible device and/or a
rotating beacon to draw the attention of the called personnel.
The latching relay and the terminal blocks are mounted inside the back box. The station selector switch, the indicator light,
“RESET” pushbutton switch, generator and handset brackets are mounted on the cover. The pushbutton is used to reset the
latching relay.
The phone is equipped with a single action push to release locking button. Both the handset bracket and the main telephone enclosure are fabricated with polycarbonate and are finished in a black powder coat. The receiver unit and the transmitter units are identical and interchangeable. In addition to the transmitter and receiver units, there is a “Press to Operate” pushbutton switch mounted on the handset for convenience. The standard coiled cord of the handset is one foot long and expands to 6 feet long when fully extended.
Features:
- Cost Effective and Proven
- Virtually Indestructible, Flame Retardant
- Operates in Extreme Conditions
- Operates Continuously With No Maintenance
- Operates Without Batteries or External Power Source
- No Software Required
- Meets or Exceeds Title 46, CFR, Subpart 113.30-3(b)
- Secure Locking Bracket For Handset
The Model VFG-LR are Surface Bulkhead Mounted Telephones that are located mainly in medium to high noise areas such as
machinery spaces and engine rooms. An audio signaling device is used to signal an incoming call.
When there is more than one Voiced Powered Telephone in the same area, the indicator light identifies which telephone is
being called. In a wide, noisy working area, the latching relay may be employed to sound an additional audible device and/or
a rotating beacon to draw the attention of the called personnel. The enclosure is equipped with an H27A type jack and cap to
accept an H39A plug for additional communication devices, such as headset.
The magneto generator and the internal audio signaling device are mounted on the cover. The latching relay and the terminal
blocks are installed inside to the back of the station box. The station selector switch, the indicator light, “RESET” pushbutton
switch, and generator handset brackets are mounted on the cover. The pushbutton is used to reset the latching relay.
Both the handset bracket and the main telephone enclosure are fabricated with polycarbonate and are finished in a black powder coat. The phone is equipped with a single action push to release locking button. The receiver unit and the transmitter units are identical and interchangeable. In addition to the transmitter and receiver units, there is a “Press to Operate” pushbutton switch mounted on the handset for convenience. The standard coiled cord of the handset is one foot long and expands to 6 feet long when fully extended.
Features:
- Cost Effective and Proven
- Virtually Indestructible, Flame Retardant
- Operates in Extreme Conditions
- Operates Continuously With No Maintenance
- Operates Without Batteries or External Power Source
- No Software Required
- Meets or Exceeds Title 46, CFR, Subpart 113.30-3(b)
- Secure Locking Bracket For Handset